Text blocks and blog posts this site, are marked with “Anchors”, i.e. short tags to locate them. To create a full address still, you manually add “#name-still”, at the end of ’ page address.
To know the names of the anchors just install the Chrome plugin called “Display Anchors”
When the anchors are visible, You can also copy the full address ’ still, with these steps:
- Place the mouse cursor on the text of ’ still
- Click with the right button
- Choose “Copy link address”
Errors Installing Dot Net 3.5
Are popping up like mushrooms new cheap Windows tablets (autumn winter 2014). The Atom processor is a quad core and the operating system a genuine Windows 8.1. Sometimes it's Windows 8.1 “Bing” (which is fine) but be careful unless RT or EC (that would not work with our applications).
Some of the new models have a lack of youth. The DotNet should already be pre-loaded, but still can't activate it. When you enable or try downloading it from the Internet, the installation stops almost immediately, with error 0x800f0906.
The network are imaginative and very complex solutions, don't follow them. The cure is simple, Open “Control Panel / Windows Update” and install all updates. Then try again to activate (or install) Dotnet, that will install quickly and without errors.
Errors due to missing or corrupted Dot Net
On some machines it may happen that the applications of the system Theremino not start. In these cases, the first thing to try is to install the "DotNet Framework 3.5?, that you download from here: Net_Framework_ 3.5 _SP1
Sometimes you install the DotNet Framework 4.0, It should also contain all earlier versions but that often is not complete. In these cases, install quietly even the DotNet 3.5. The 3.5 not a problem to version 4 and complete the missing parts.
In some rare cases it happened that the Dot Net 3.5 installed but damaged. In these cases, trying to uninstall it and then reinstall it appeared a message asking if you would rather “Repair it”. Repair has fixed the problem.
Errors due to corrupted registry
On some machines it may happen that some applications of the system Theremino not start due to the following error:
Italian: Unable to load data from the counter name because an invalid index has been read from the registry
ENGLISH: Cannot load Counter Name data because an invalid index ' X’ was read from the registry
This error is sometimes referred to as its only computer to 32 bit but, Since even the 64 bits have a part relating to the applications to 32 bit, can occur on all operating systems.
To correct this error, some say reinstall Windows, but it is better to run the following commands:
– Start a command prompt as an administrator with the following sequence:
– Press the Start button
– Type CMD without sending’
– Press CTRL + SHIFT + ENTER
– Type cdwindowssystem32, and then press enter
– Type LODCTR/R and press enter
For more information read here: http://support.microsoft.com/kb/300956/it
Errors due to lack of DirectX
On some machines it may happen that some applications of the system Theremino not start due to a lack of the right version of DirectX. Applications that use DirectX are principally Theremino3D, applications using the WebCam and some applications that use sounds in a particular way.
If you have any questions about, install a DirectX plus it never hurts. We recommend that you install the DirectX 9.0 c off-line version from here: http://www.microsoft.com/en-us/download/details.aspx?id=8109
Turn off updates to Windows10
This procedure completely disables Windows Update. The computer will not download updates and therefore over time you will use an operating system that is not updated. It remains possible to manually update the virus definitions of Defender.
Disable updates can be useful for those who use the computer for automation or to avoid problems during short periods, When there are errors in the updates and ’ anticipation that these errors will be corrected.
We do not recommend keeping Windows Update turned off for too long. We recommend that you turn it back on at least once every three months, maximum one year, and give him a night time to discard any accumulated updates.
Disable updates is easy, the following procedure seems long, but once you have learned the run in seconds.
1) Open the Task Manager (Task Manager) of Windows 10.
2) Open the tab “Services” (at the top right).
3) Click the blue writing “Open Services” (in the lower part of the window).
4) Make sure the list is in alphabetical order.
5) If unsorted click “Name” to bring up the triangle with the point at the top.
6) Scroll down the list of services until you find “Windows Update”.
7) Double click with the mouse on “Windows Update”.
8) Service Properties window opens “Windows Update”.
9) In the tab “General”, at line “Startup type”, Select the ’ option “Disabled”.
10) Confirm by clicking the button “Apply” (you have to press it, OK alone is not enough)
11) Close the window with “Ok”.
To reactivate “Windows Update” you do exactly the same thing but at row nine you choose “Manual”.