信号滤波


伽马能谱测量的信号滤波

您看到此模拟的筛选是第一次研究的一部分, PmtAdapter 的最终模式在这里: www.theremino.com/technical/schematics

三个脉冲 (底片) 在仿真中可见的:
红色: 光电倍增管产生冲量 ( 1我们 – 10 伏特 )
白色: 提高后的第一个单元下山 ( 为 10 我们 – 1 伏特 )
绿色: impulso dopo la 内力地窖帕萨特男低音 ( 为 300 我们 – 20 MV )

只有第三种冲动 ( 有时被称为 “高斯” 因为它的形状 ) può essere campionato con precisione da una scheda 音频. 第二个脉冲, 据放缓, 仍然有顶端尖尖的只有很少会完全对其尖端的示例. L ’ 不准确采样产生的行扩大. 这种效应是通过冲动与窗体最小化 “高斯”, 它们提供了一个宽广的水平区域, 尽量减少错误,即使是在 48 千赫.

与软件观众观看脉冲时这些窗体是很枯燥, 荣誉德拉 limitata 班达 passante 德拉 scheda 音频, 和也似乎不够宽 (几十微秒) 但不要抱太大希望: 没有双重过滤 RC 传入冲动至声卡是窄而尖. 然后传播出来,但, 虽然他们没有看到更多的特征, 他们已经损坏.


与筛选器和 ADC 硬件从上个世纪的比较.

这些硬件模块的打火石是多么的漂亮吗!

太糟糕了,片刻之后’ 多年的电位器开始从头开始, 开关使联系人只能在星期四,, 即使在最佳条件下, 结果均低于软件.

这些 Adc 是快速的硬件 (但它是没有多大) 但在另一方面有的唯一的信号噪声比 60 DB vs 110 DB 访问由 ADC 在最近的音效卡 (这些真的很需要)

他们的电力供应也很大声 (从 5 对 MV 50 MV pep) 与我们目前使用的电源供应器 (在下 200 UV pep)

它不是只是大约支出尽可能多或尽可能少, 有 30 多年的改进.

评论
当然,你可以留下评论, 问题和建议.

  1. 里维奥 说:

    用户 81lmc7101, 作者 http://www.youtube.com/watch?v=P_WpkaLX0BQ 写道:: “很好和强大的软件! 谢谢! 顺便说一句, 低能量分辨率是弱于 PRA. 请, 告诉我关于这个软件的理想脉冲形状 – 我将使筛选器。”

    没有筛选器
    ——————————————————
    也不过滤也是可能要降到决议 7% FWHM 使用 “基线恢复” 和 “死区时间”
    – 使用采样的频率 192 千赫 (没有过滤器势在必行)
    – 设置为 50 和 50 的 “基线恢复” 和 250 的 “死区时间”
    – 不发送到音频卡输入脉冲的幅值不超过一些伏. (用一种真正的硬件示波器测量) (备注 1)
    – 设置所有 “录音合成器” 滑块拖到不超过 70%
    – 如果你的脉冲到其他太多近一, 请提高放射性样品到闪烁体的距离 (要不超过 200..500 每秒脉冲)

    备注 1
    音频卡衰减很多--波段脉冲 (脉冲 < 50uS) To get a useful signal with so short pulses the only method is to increase the pulse voltage. Someone sends to the sound card pulses of 1uS with a height of 30 Volt !!!!! In this situation happens the following: - the sound card input components are completely saturated - the linearity of the high energies is loosed (the poor PMT is not the responsable of this) - the antialias filter produces tons of ringing - the distorsions produced creates so much noise that the low details are completely masked With filter ------------------------------------------------------ The best filter is composed by two low pass cells With only one cell the top is too much sharp to sample it with precision. (please analyze the dots on the pulse top in the Pulse visualizer) It is also important to increase the rising time enought to eliminate ringings And, if possible, to completely eliminate the baseline shifting using "bipolar pulses", (pulses with the same positive and negative areas" Please write on our Blog so, with the help of the community, we will find the best circuit and schematics. In this page, with the halp of the community, we will find the best and simplest filter. Bye Livio

  2. 阿诺德 · 丹尼尔森 说:

    我想看到数字滤波器输入到 theremino 马华有一个高频率截止可调至 2 khz 或更高. 这是为了滤除噪声在高频率结束了. 将有可能帮助有点与脉冲形状但真的意味着尽量减少噪音楼.

留言

您的电子邮件地址将不会发布.